Good Sam Club Open Roads Forum: Search
Open Roads Forum Already a member? Login here.   If not, Register Today!  |  Help

Newest  |  Active  |  Popular  |  RVing FAQ Forum Rules  |  Forum Posting Help and Support  |  Contact  



Open Roads Forum  >  Search the Forums

 > Your search for posts made by 'youracman' found 10 matches.

Sort by:    Search within results:
  Subject Author Date Posted Forum
RE: TPMS for the alcoa wheels

On mine, Bob.... it is a mix (typical), i.e., a steel wheel inboard and an Alcoa outboard. Both have very little clearance over the hub and are, in fact, a bit of a tussle to get off. The lug nuts are the "built-in-washer" type.....not conical and they only call out 140 ft-lb of torque .... stamped on the lug nuts. That is the config for 16" wheels, dunno about larger ones. I believe the GVWR is the same for all steel as for the Alcoa-wheeled rigs with 16" wheels.....if that's germane.
youracman 09/11/20 07:30pm Class C Motorhomes
RE: TPMS for the alcoa wheels

Aren’t most all aftermarket wheels lug centric , including Alcoa ? If that’s the case , which i think it is, then that would explain why they are sensitive to being overloaded ? The lugs would center and carry the weight instead of the hub , like an OEM steel wheel. If that’s the case then it’s imperative to weigh your rig.
youracman 09/11/20 07:17pm Class C Motorhomes
RE: TPMS for the alcoa wheels

Just my 'sperience, Hank: I ordered solid (chrome plated brass, I believe) "Dually" valve stems from here: https://www.shinyrv.com/product-category/dually-valve-stems/ They have a "CONTACT" button on their site. I tried to go to the main supplier for Dually Stems, but they wanted to know what angle I needed. I didn't have a clue, so I contacted the folks at "Always Shiny" and they knew exactly what I needed. IIRC the price back then was $115 with free shipping. I had them installed on the duals at Les Schwab ..... for about $85 (they said an easy job cuz all they have to do is "break the bead" to install....no tire dismount needed.) Know that it is nigh impossible to spin balance the inside dual with the 7-inch long valve stem so I installed "Centramatics" ....... I now doubt that was needed as some folks do not balance the rears at all; probably could just spin balance the outer dually and call it a done deal. The hardware from Always Shiny included a rubber "stabilizer" that goes in one of the "hand holes" on the Alcoa rim to stabilize the long inside stem. I wasn't thrilled with the fit on those stabilizers, but they have never moved.....so they work. I use a TST system with the cap sensors. Never had a problem since installing this setup about 3 years ago. One nice feature: I can check the pressure or air up any tire without even getting down on one knee...... so I am well satisfied. I personally like the cap sensors better than the flow through type (I've used both) however it is a bear to service the cap sensors with new batteries, and O-rings (the flow throughs are easier) ..... but I go ahead and do it each winter for the upcoming travel season. I didn't need to do anything to the steer tires to use the TST cap sensors. A little tight, but not real difficult to install or remove the sensors. I did modify my sensors by removing the "theft prevention' feature. Simplifies things, IMHO. Hopes this helps. As always, YMMV. Stay safe.
youracman 09/11/20 04:17pm Class C Motorhomes
RE: Adding 2nd AC to Class C

jdc1, I was thinking the same thing. We don't need it all the time...but are planning trips out west where it's HOT...and our 34 foot C will be HOT with that front-mounted AC unit....but installing a rear-section unit (as mentioned, in bedroom), and pluggin it in when needed, simplifies matters a ton. Hi Robert- I have not done this mod, but there were a couple of long threads over on irv2 concerning it. I can't seem to find them now, but IIRC, both guys ended up using a second, dedicated cord for the 2nd AC as suggested earlier. I too would have to go with external ceiling wiring but the metal raceway channel with a snap cover (sold by HD and others) could be screwed to the ceiling and would not look all that obtrusive, IMHO. Both the installs posted on irv2 used "local control" AC's ; i.e. no wall t'stat to complicate things and of course the AC's fit in the 14X14 hole just fine. You would almost certainly need to use a 50A pedestal; as I understand it, even if a 30A site has a 20A outlet, you are limited to 30A total. I also read a post or two where it was stated that new campground regulations allow only one cord to be connected from an RV to the pedestal, period ….. not good news, for sure. If that's true, one would have to turn their Class C into a 50A coach, basically, in order to add the needed 20A which could be done, but a lot of work and expense. Here is a link (Google) with a well-documented install where the guy plans to use a 2nd cord for the add'l AC. The most interesting thing I found was the nifty waterproof wall connector to bring the extra/new power into the coach.https://www.google.com/search?source=hp&ei=V9_nXsy3H5DXtAarlafIAQ&q=add+2nd+ac+to+rv&oq=add+2nd+ac+to+&gs_lcp=CgZwc3ktYWIQARgAMgIIADICCAAyBggAEBYQHjIGCAAQFhAeMgYIABAWEB46BQgAEIMBOgUIABCxAzoECAAQClDqHVjZTGDhZGgAcAB4AIABV4gB0AeSAQIxNJgBAKABAaoBB2d3cy13aXo&sclient=psy-ab#kpvalbx=_gO_nXvrpHNWwtAbjgbSQAg27 Good luck on the project, and safe travels
youracman 06/15/20 03:58pm Class C Motorhomes
RE: Cold in West Yellowstone...

Phil- Re how to determine that your tank heaters are working: FWIW, just thought I would pass along my 'sperience since I had to replace the heaters on my rig a couple of years ago (the OEM gray tank heater pad was a so-so install by the factory and was lifting around the edges plus the original owner had damage on the black tank due to a blowout and the service folks who installed his replacement black tank did a turibble, turrible job on that heater.) Our tanks are likely about the same size, so my data may be helpful. I installed Ultra Heat pads after a bad experience with a poorly made (cheaper) brand. WBGO uses (made in the USA) Ultra Heat ….. same as almost all RV manufacturers, I believe. Each of the 2 large pads draw about 5.5 amps and I also have an elbow heater which draws just under 1 amp. The large pads have a built in Tstat that turns on at 44F and off at 64F; the elbow heater has no Tstat …. it is constant on when powered up. I'd wager your current draws are in that "ballpark". For a pre-trip checkout one can use a clamp on DC ammeter (takes 2 people.) One person holds a zip lock bag of ice cubes on the "bulge" at each of the pads (that's where the Tstat is) and the other observes current flow when the stat kicks in. (I did this to verify operation after my installation.) Mfr says to have at least a couple of inches of fluid in the tanks to operate the heaters (probably more to prevent excessive Tstat cycling than anything else, I believe.) I only have these installed in case I get "caught" with a surprise cold front as we like Fall season travel the best. I carry my clamp-on meter along and would plan to look for 12 add'l amps off the coach batteries when the tank heater switch was thrown to verify the pads were drawing current …. but have never had to use it. Sounds like the OP has a built-in meter which would do the same thing ………… cool. BTW- The WBGO tech I talked to about the heaters said the rig should be good to about 20F if I opened the inside cabinet doors and turned on the tank heaters ………. but I overheard him talking to others around him when I asked that question and I believe his answer was just an educated guess. West Yellowstone campers would be a better source of knowledge, me thinks. :^) Stay healthy, and safe travels.
youracman 06/08/20 09:48pm Class C Motorhomes
RE: Final accounting, 14 years with a Super C

To the OP: What a GREAT post. Thank you for taking the time.
youracman 05/30/20 07:30pm Class C Motorhomes
RE: tapping the top of awning to project it from the sun

My trailer has been parked under the brutal sun of the desert for 7 years. Shortly after I got it, I got some 6” wide Eternabond and put a layer on top of the awnings when rolled up. It’s flexible so it rolls up without a problem and is still flawless after 7 years. No worries about having to install and remove temporary covers. Amazing! I use EB tape on the roof for flat seams; love the stuff. Your use on the awning is an interesting application (I think you are a trailblazer where EB is concerned.) SOoooo .... it works when parked for 7 years; have you had it out on the road at highway speeds much? Wondering about headwinds or maybe worse, blustery side winds if I were to apply it to the awning (and the slide out cover) on my rig. On second thought, I remember lots of BIG TIME spring winds (like 80 MPH) when I lived in the Mohave desert (most deserts are like that I believe) ..... so maybe "no sweat"? I guess I would plan on a "dust/dirt" line at the sticky edge of the EB tape, but I could live with that. Thanks for your post. Velly intellesting reading, for sure. Be safe ...................
youracman 05/21/20 04:49pm Class C Motorhomes
RE: Replacement for Onan 4000

Won't cut it, Cody. Your AC + converter will require approx 2000-2200 watts, steady state. Note that this genny will deliver 1600 watts steady state; not 2000. Suggest you not give up on the Onan just yet and, instead, find someone who will troubleshoot it rather than throw parts at it. The fuel pump/filter often are culprits; I actually had to replace the magneto in mine (rare problem) and it has been running fine for 4 years since. Others will have advice as well......there are a LOT of satisfied owners out there and many have a ton of expertise as well. Good luck on the fix.
youracman 04/01/20 11:26pm Class C Motorhomes
RE: Forest River Lexington tire issue

Just get Set Of These and have them installed and all your problems will be solved. Long lasting,mine have been over 10 years,and it will make your tire pressure checking fast and easy. Excellent advice. I got mine at a different source, but your best price is here: yourtireshopsupply.com I haven't had mine installed but a couple of years now, but zero trouble; and I can check my tires without even kneeling down! They will come with stabilizers for the long (inboard) dual so no worry about about wobble/vibration when adding TPMS sensors onto the end of the stem. Les Schwab charged me about $80 to install IIRC. They said it is fast/simple to do because they only have to "break the bead" to install...... no need to demount the tire from the rim. A shop that does lots of truck tires is the place to go IMHO. I do use Discount Tire for my car(s) but for sure not my MH. For the inner dual at least, it is not usually possible to spin balance because of the length of the stem; I installed Centramatics at the rear, but there are other options, of course. Good luck with the fix, and safe travels to ya.
youracman 01/28/20 07:03pm Class C Motorhomes
RE: Dually Valve Stems

One route to go on getting curved stems installed: I got mine here: https://www.shinyrv.com/product/dually-valve-stems-for-motorhomes-with-alcoa-wheels-2-hand-hole-dl4ac/ If you call them at 714-642-3646 they will know the exact curvature you need etc and will ship them to your door. You may save a few bucks shopping around but this was sure handy for me. The hardware I got included the rubber inserts to stabilize the longer stem so no worry with installing a tire pressure monitor sensor at that location. As enblethen posted, any truck tire shop will install them. I used Les Schwab............. about $85 IIRC. One of the downsides: The inside dual will have a valve stem that is too long for spin balancing. I just installed Centramatics on the rears but you could have the tire shop use beads. Good luck with the upgrade...... and save travels to ya. You will be very happy with the results.
youracman 01/14/20 09:53am Class C Motorhomes
Sort by:    Search within results:


New posts No new posts
Closed, new posts Closed, no new posts
Moved, new posts Moved, no new posts

Adjust text size:




© 2020 CWI, Inc. © 2020 Good Sam Enterprises, LLC. All Rights Reserved.